Tips & Tricks
Asus 1215N problema hard disk con Ubuntu
Installando Ubuntu sul netbook Asus 1215N, quando è alimentato dalla batteria, l'hard disk continua ad andare in standby (spin down) causando un tichettio molto fastioso e dannoso per lo stesso. Collegandolo all'alimentatore esterno, l'hard disk funziona correttamente. Questo l'ho riscontrato su tutte le versioni di Ubuntu Linux (ultima, ad oggi, la 11.04). Per risolvere il problema basta editare il file hdparm in questo modo: gedit /etc/hdparm.conf ed inserire le seguenti righe alla fine /dev/sda { apm = 254 apm_battery = 254 } e riavviare. |
Problema su Garmin Etrex Venture HC
Premetto che sono pienamente soddisfatto dall'apparecchio in oggetto, tuttavia riporto la soluzione ad un problema molto diffuso, che mi è capitato, e fortunatamente ho trovato la soluzione sui blog del settore. Il problema: quando la memoria è troppo piena (il modello citato è HC, cioè senza memoria esterna con versione software 3.10) il Venture HC si spegne da solo (lo stesso vale per il Summit HC). La soluzione: svuotare la memoria cancellando le mappe e i tracciati in eccesso. Sul sito Garmin.it scrivono che l'aggiornamento del software alla versione 3.30 toglie questo problema. A me è capitato di non riuscire più ad accenderlo; in pratica visualizzava la prima schermata e poi si spegneva dopo qualche secondo, quindi non potevo connetterlo al PC per cancellare i dati. In tal caso basta accenderlo tenendo premuto il tasto INVIO (joystick) entrando nella modalità "test" e poi lo si collega tramite usb al PC. Oltretutto dopo averlo aggiornato alla versione 3.30 senza errori riportati, non mi si accendeva più e non si connetteva più al pc. In questo caso è bastato accenderlo tenedo la leva del joystick verso l'alto, appena il PC lo riconosce si può far ripartire l'aggiornamento (io ho reinstallato la 3.10). Dai vari blog che ho consultato questi due problemi sono molto diffusi, riporto qui sotto alcune delle soluzioni: I had the same problem with automaticaly turn off in 10 seconds After more frustrating search and help from Garmin (The wanted me to send them the Unit) But before shipping, I found this thread by google..And I was able to reset my Garmin by holding down enter, page, and power at the same time - in 5 seconds. (The 2 right buttons and the button on top) After that it was now possible in the trip computer to reset all data. It worked in minutes ... and then the problem was back. After that I erased all tracks (It was showing a warning 99%) Now the unit is running again without missing it in a "repair" period. Thanks for the help My personal conclusion is, that Venture and Summit with 24 MB have problems, when the memory is used for trip, tracks .. and perhaps small map. Now, here’s where it gets tricky. Since the unit wasn’t recognized by the firmware updater on its own, customer support gave me the crazy keypad combination to trick the updater to see your USB GPSr: hold down the power button (on the top of the unit) and push the directional button in the up (“^”) position. While holding those buttons down, double click on the Updater.exe file in the directory where the firmware updates were extracted to. If this worked for you, then your GPSr should now show up for the firmware update program. While still holding down the two buttons, make sure your GPS device is selected, and then click the “OK” button to start the firmware update. During the entire firmware update process you need to hold those buttons down. The update can take several minutes, and your fingers will start to HURT, but you need to hold them down. Once the update has completed, you can relax your fingers and you should now be able to start up your GPSr. I can solve this by not solving it. First I tried reset the unit to default settings: hold down the power, page, and enter buttons at the same time, a message, "do you really wan to reset..." will appear. Select "yes." If the unit reboots, hurrah. |
1-2 of 2